Damage evolution around white etching layer during uniaxial loading

Rolling contact fatigue cracks and thermally induced defects are common problems in the railway industry especially as demands for increasing loads, speeds, and safety continue to rise. Often, the two types of defects are found together in the field, however, whether one causes the other to occur is not completely agreed upon. The effect of thermal damage, in the form of a martensite spot on pearlitic steel test bars, on the fatigue life in uniaxial low cycle fatigue experiments was investigated by the authors. However, the focus of the current work was to characterize the damage evolution from the low cycle fatigue (LCF) tests and correlate the crack initiation and propagation with the initial thermal damage. Residual stress measurements, digital image correlation, and X‐ray tomography were used to characterize the effects of the thermal damage before, during, and after fatigue testing, respectively. It was found that the thermal damage causes strain accumulation and crack initiation at the interface between the two materials. The strain evolution was visualized using digital image correlation (DIC), clearly showing the strain concentrations at the top and bottom of the white etching layers (WEL), where the residual stresses are also most tensile. X‐ray tomography confirmed the planar crack growth from the martensite spot.     

大气次声源定位算法及误差分析

逐步多通道相关方法是定位次声源的主要方法。该方法会忽略阵元的海拔高度差,从而引入误差。文章分析了基于广义互相关的时间延迟估计算法,讨论了基于时延的平面波入射角定位方法。着重研究了逐步多通道相关方法的误差来源,确定了基于时延的定位方法是产生误差的主要原因,明确了大气次声源定位误差来源于忽略了阵元间的海拔高度差。基于最小二乘法推导了在不考虑阵元高度的情况下计算次声波入射角的方法。对存在高度差的4元中心三角阵型进行了误差仿真实验,在忽略阵元海拔高度差的条件下,各方向入射的次声波角度定位误差最大达到4°,特定阵型的阵元最大海拔高度差与入射角度计算误差成线性关系,并探讨了入射角度计算误差对主要参数和后续定位的影响。     

Advances and perspectives on one-dimensional nanostructure electrode materials for potassium-ion batteries

Potassium-ion batteries (PIBs) have aroused considerable interest as a promising next-generation advanced large-scale energy storage system due to the abundant potassium resources and high safety. However, the K⁺ with large ionic radius brings restricted diffusion kinetics and severe volume expansion in electrode materials, resulting in inferior actual rate characteristics and rapid capacity fading. Designing electrode materials with one-dimensional (1D) nanostructure can effectively enhance various electrochemical properties due to the well-guided electron transfer pathways, short ionic diffusion channels and high specific surface areas. In this review, we summarize the recent research progress and achievements of 1D nanostructure electrode materials in PIBs, especially focusing on the development and application of cathode and anode materials. The nanostructure, synthetic methods, electrochemical performances and structure-performance correlation are discussed in detail. The advanced characterizations on the reaction mechanisms of 1D nanostructure electrode materials in PIBs are briefly summarized. Furthermore, the main future research directions of 1D nanostructure electrode materials are also predicted, hoping to accelerate their development into the practical PIBs market.     

融合重检测机制的卷积回归网络目标跟踪算法

针对基于人工特征的背景感知相关滤波（CACF）算法在形变、运动模糊、低分辨率情形跟踪效果较差以及跟踪器遇到严重遮挡等情形容易陷入局部最优而导致跟踪失败的问题，提出一种融合重检测机制的卷积回归网络（CRN）目标跟踪算法。在训练阶段，将相关滤波作为CRN层融入进深度神经网络，使网络成为一个整体进行端到端训练；在跟踪阶段，通过残差连接融合不同网络层及其响应值，同时引入重检测机制使算法从潜在的跟踪失败中恢复，当响应值低于给定阈值时激活检测器。在数据集OTB-2013上的实验表明，所提算法在50个视频序列上精确度达到88.1%，相比原始CACF算法提高9.7个百分点，在具有形变、运动模糊等属性的视频序列上相比原始算法表现更优秀。     

Estimation of Antenna Correlation Coefficient of N-Port Lossy MIMO Array

This paper proposes a simple yet accurate method for estimating the antenna correlation coefficient (ACC) of a high-order multiple-input multiple-output (MIMO) antenna. The conventional method employed to obtain the ACC from three-dimensional radiation patterns is costly and difficult to measure. An alternate method is to use the S-parameters, which can be easily measured using a network analyzer. However, this method assumes that the antennas are highly efficient, and it is therefore not suitable for lossy MIMO antenna arrays. To overcome this limitation, we define and utilize the non-coupled radiation efficiency in the S-parameter-based ACC formula. The accuracy of the proposed method is verified by the simulation results of a 4-port highly coupled lossy MIMO array. Further, the proposed method can be applied to N-port arrays by expanding the calculation matrix.     

不同熄焦方式对40kg焦炉焦炭质量的影响

不同熄焦方式对焦炭的冷态强度、热态强度以及生产焦炉的工艺特点均有影响,为了更好地指导40 kg试验焦炉的生产,需对比分析水熄焦、干熄焦方式对焦炭质量的影响。选用4种不同炼焦煤和1种生产配合煤,利用40 kg级实验焦炉炼制焦炭,分别采用蒸汽熄焦与水熄焦方式对40 kg焦炉炼制的焦炭进行冷却,检测熄焦后焦炭的工业分析、机械强度及热性质等性能指标,对比分析2种熄焦方式对焦炭质量的影响,并研究2种熄焦方式下焦炭与生产干熄焦的焦炭质量关系。结果表明,相对水熄焦,蒸汽熄焦的焦炭水分较稳定(小于1%)、成焦率有所提升,改善了焦炭质量,其中1/3焦煤冷强度的改善最为明显,气煤与1/3焦煤的热性质改善最为明显,肥煤的成焦率提升最大;蒸汽熄焦与生产干熄焦的焦炭质量指标更接近,机械强度M 40一致、M 10数据高出2.5个百分点,热性质CRI数据高出8.1个百分点、CSR低出10.4个百分点。焦化企业可参照试验结果,进一步优化40 kg实验焦炉熄焦工艺及调整生产与试验焦炉的相关性。     

组合赋权的TOPSIS在冲击地压危险性评价中的应用

为了合理准确地评价煤矿冲击地压危险性,在现有评价冲击地压危险性实例的基础上,从煤矿地质因素和开采因素2个方面,选取10个主要的影响指标,利用熵权法和指标相关性权重法分别计算影响冲击地压危险性的各评价指标权重,再根据组合赋权的方法得出各指标的综合权重,构建基于逼近理想解理论的冲击地压危险性评价模型。以重庆砚石台煤矿为例,选取20组评价冲击地压危险性样本数据进行分析,确定评价冲击地压危险性的最优和最劣状况,然后计算出各个评价方案与最优和最劣状况的距离,最后综合最优与最劣距离,确定评价对象的相对贴近度。应用结果表明:评价结果与实际情况一致,且该模型相较其他模型的评价结果更加科学准确,表明该方法有良好的实用价值。     

Genetic (co-)variation of methane emissions,efficiency, and production traits in Danish Holstein cattle along and across lactations

Methane emissions in ruminant livestock has become a hot topic, given the pressure to reduce greenhouse gas emissions drastically in the European Union over the next 10 to 30 yr. During the 2021 United Nations Climate Change conference, countries also made collective commitments to curb methane emissions by 2050. Genetic selection for low-methane-emitting animals, particularly dairy cows, is one possible strategy for mitigation. However, it is essential to understand how methane emissions in lactating animals vary along lactation and across lactations. This understanding is useful when making decisions for future phenotyping strategies, such as the frequency and duration of phenotyping within and across lactations. Therefore, the objectives of this study were to estimate (1) genetic parameters for 2 methane traits: methane concentration (MeC) and methane production (MeP) at 2 parity levels in Danish Holstein cows across the entire lactation using random regression models; (2) genetic correlations within and between methane traits across the entire lactation; and (3) genetic correlations between the methane traits and economically important traits throughout first lactation. Methane concentration (n = 19,639) records of 575 Danish Holstein cows from a research farm measured between 2013 and 2020 were available. Subsequently, CH₄ production in grams/day (MeP; n = 13,866) was calculated; MeP and MeC for first and second lactation (L1 and L2) were analyzed as separate traits: MeC_L1, MeP_L1, MeC_L2, and MeP_L2. Heritabilities, variance components, and genetic correlations within and between the 4 CH₄ traits were estimated using random regression models with Legendre polynomials. The additive genetic and permanent environmental effects were modeled using second-order Legendre polynomial for lactation weeks. Estimated heritabilities for MeP_L1 ranged between 0.11 and 0.49, for MeC_L1 between 0.10 and 0.28, for MeP_L2 between 0.14 and 0.36, and for MeC_L2 between 0.13 and 0.29. In general, heritability estimates of MeC traits were lower and more stable throughout lactation and were similar between lactations compared with MeP. Genetic correlations (within trait) at different lactation weeks were generally highly positive (0.7) for most of the first lactation, except for the correlation of early lactation (<10 wk) with late lactation (>40 wk) where the correlation was the lowest (<0.5). Genetic correlations between methane traits were moderate to highly correlated during early and mid lactation. Finally, MeP_L1 has stronger genetic correlations with energy-corrected milk and dry matter intake compared with MeC_L1. In conclusion, both traits are different along (and across) lactation(s) and they correlated differently with production, maintenance, and intake traits, which is important to consider when including one of them in a future breeding objective.